A simple formulation for predicting the ultimate strength of ships

The aim of this study is to derive a simple analytical formula for predicting the ultimate collapse strength of a single- and double-hull ship under a vertical bending moment, and also to characterize the accuracy and applicability for earlier approximate formulations. It is known that a ship hull will reach the overall collapse state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and the tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical equation for calculating the hull ultimate strength is obtained. A comparison between the derived formula and existing expressions is made for largescale box girder models, a one-third-scale frigate hull model, and full-scale ship hulls.List of symbols A _B total sectional area of outer bottom - A _B total sectional area of inner bottom - A _D total sectional area of deck - A _S half-sectional area of all sides (including longitudinal bulkheads and inner sides) - a _s sectional area of a longitudinal stiffener with effective plating - b breadth of plate between longitudinal stiffeners - D hull depth - D _B height of double bottom - E Young's modulus - g neutral axis position above the base line in the sagging condition or below the deck in the hogging condition - H depth of hull section in linear elastic state - I _s moment of inertia of a longitudinal stiffener with effective plating - l length of a longitudinal stiffener between transverse beams - M _E elastic bending moment - M _p fully plastic bending moment of hull section - M _u ultimate bending moment capacity of hull section - M _uh ,M _us ultimate bending moment in hogging or sagging conditions - r radius of gyration of a longitudinal stiffener with effective plating [=(I _s /a _s )^1/2] - t plate thickness - Z elastic section modulus at the compression flange - Z _B ,Z _D elastic section modulus at bottom or deck - slenderness ratio of plate between stiffeners [= (b/t)(_y/E)^1/2] - slenderness ratio of a longitudinal stiffener with effective plating [=(l/r)(_y/E)^1/2] - _y yield strength of the material - _yB , _yB , _yD yield strength of outer bottom, inner bottom - _yS deck, or side - _u ultimate buckling strength of the compression flange - _uB , _uB , _uD ultimate buckling strength of outer bottom - _uS inner bottom, deck, or side     

车载网络安全的系统设计研究及关键技术开发

本文介绍了车载网络安全的系统设计研究及关键技术开发,以应对黑客通过网联攻击车辆,建立智能网联汽车车内网络信息安全交互模型;分析“外部网络环境”与“车内ECU群体”之间进行“信息资源”交互过程中的安全风险,研究其对车内网络信息安全的破坏机理;利用基于密码学理论研究车内网络安全通信协议的设计方法,解决车内网络在智能网联汽车环境下面临的信息安全问题。     

进气预混甲醇降低柴油机碳烟与NOx排放的影响参数研究

在485QDI自然吸气直喷式柴油机上研究了不同喷嘴、不同供油定时、不同喷醇的起点对进气预混甲醇发动机的碳烟、NOx排放和经济性的影响。研究结果表明，为了降低碳烟和NOx排放以及提高燃油经济性，与燃用纯柴油的发动机相比，进气预混甲醇发动机的柴油喷射定时可以保持不变或稍小，但燃油喷嘴的孔径应适当减小，预混甲醇的发动机负荷起点应适中。     

材料、结构和工艺因素对高强度螺栓疲劳性能的影响试验研究

对影响高强度螺栓疲劳性能的材料、结构和工艺等因素进行了较广泛的对比试验研究。比较了6种材料疲劳试样的疲劳性能;考察了硬度、再回火、去应力退火、表面脱碳、滚丝/磷化的先后顺序、头下圆角粗糙度、滚丝轮螺纹牙形、头下圆角过渡形式等因素对高强度螺栓疲劳性能的影响。     

高速公路路堤和路面软基病害检测及加固处理

某高速公路 K1 0 4 2 0 0～K1 0 6 5 0 0段穿过鱼塘 ,路堤采用钢渣水中挤淤法施工 ,通车后路面出现了严重的纵向裂缝、车辙、沉陷 ,影响了路面的使用性能 ,同时路堤存在滑动的隐患 ,必须进行加固处理。为此 ,首先通过系统检测 ,分析路面裂缝产生的原因 ,然后提出针对性的加固处理方案 ,最终实施加固处理施工 ,所取得的成果对其它高速公路的维修加固具有参考价值     

滑模摊铺水泥混凝土路面施工配合比计算方法

本文针对我国目前大规模采用滑模摊铺机施工高速公路水泥混凝土路面，为适应滑模摊铺施工机械性能，充分发挥滑模摊铺机施工优势，确保水泥混凝土路面强度、平整度等指标而提出的水泥混凝土施工配合比计算方法。     

低强度桩复合地基处理桥头跳车现场试验研究

介绍了浙江台州浃里陈大桥成功地采用低强度混凝土桩复合地基处理桥头跳车问题，同时通过现场载荷试验、桩顶和桩间土的土压力测试以及沉降观测，较全面地研究了低强度桩复合地基承载力和桩土受力特性以及沉降变化规律，得到了一些可供理论研究和工程实践借鉴的有益结论。     

潭邵高速公路顺层滑坡整治

通过对某顺层古滑坡的现场调查，分析判断出古滑坡的滑动范围、滑动面，并对滑动面抗剪强度参数进行了反分析计算。据此对古滑坡体进行了初步整治设计，实际整治时未进行防水措施，抗滑指标进一步下降，并对此时软化滑动面抗剪强度进行了计算分析。结果对K89-95段的调查分析，对此区段的切方边坡违背工程地质选线原则导致的后果进行了反思。     

大跨径无桥台斜腿刚架桥的展望

无桥台斜腿刚架桥是近年发展起来的一种新桥型。通过研究其受力特性和构造形式，指出该桥型向大跨径发展的可能性。     

闽江下游堤防护岸工程施工技术

阐述福建闽江下游堤防护岸工程的原状和维修的必要性 ,提出护岸工程中水下护脚和水上护坡的几种不同结构形式和施工技术并对各自的适用性和优缺点进行评述